artificial stone slab machinery suppliers

artificial stone slab machinery suppliers

There are many artificial stone slab manufacturers. Today we will introduce how to choose a good artificial stone slab machinery suppliers.

Quartz stone concrete application, can not avoid two pieces of splicing or even multiple pieces of splicing, because the hardness of quartz stone up to 7 level moth, splicing, in order to make the whole look like a whole, the test of quartz stone manufacturers and processing master technology. Specifically how to operate, we can click the way to operate.

The mutual inspection of all the large and small materials includes the direction of the skirt, the position of the edge, the direction of the slope, the length and the width of the skirt, and the color difference between the spliced plates. Before making, we need to understand the edge structure and the size of the small materials, so that we can know what we know and not to stick the wrong edges.

Place the bottom of the panel on the table and on the worktable, check the smoothness of the adhesive surface, wipe off the stains with clean balls, rinse with clean water, clean and dry with a wind gun or dry cloth to stick to the surface. According to the thickness of the table, select the corresponding height of the skirt reinforcement bar (the height of the reinforcing bar h=h - D), and evenly apply the coloring cloud and stone glue to bond the light surface to the bottom of the table, and the outer edge of the reinforcing bar is leveled with the slope of the panel.

It is clamped with G clip or a type clip to clear the residual glue. Evenly smear the coloring and coloring micelle with the slope side of the panel and the side side of the reinforcing bar, put the slope of the skirt on the glue, squeeze the air, clamp the edge of the skirt with the panel with the F clip, and tap the moderate strength with a rubber hammer. It is the flat of the skirt and the panel at the corner. A clip is clipped at every 100-150mm. Then use the A clip to clamp the skirt and reinforcement plate between each two F clips to clean up the residual glue. The bottom of the reinforcement class is flat with a flat flat surface, so that the width of the skirt is 65mm, and the clip is fixed every 200mm.

Type and innovation of artificial quartz machinery

Put the bottom of the panel up on the worktable, check the smoothness of the adhesive surface, wipe off the stains with clean balls, rinse with clean water, clean and dry with a wind gun or dry cloth to stick to the surface. According to the thickness of the table, select the corresponding height of the skirt reinforcement square (the specification of the reinforcing square is 35 x h, h=h-2d), and evenly smear the color and marble glue to bond the reinforcing block to the bottom of the table every 200mm away, and the reinforcing square is flat on the side of the panel. It is clamped with G clip or a type clip to clear the residual glue.

Evenly smear the coloring and coloring gels on the side side of the panel and the side of the reinforcing bar, put the slope of the skirt on the glue, squeeze the air, clamp the edge of the skirt with the panel with the f clip, and use the rubber hammer to moderate the strength, make the edge of the skirt flush with the panel, and clip a clip at every 100-150mm. Then use the G clip to clamp the skirt and reinforcement block between each two f clips to clean up the residual glue. The bottom of the reinforcing plate is flat and adhered to a flat strip of smooth surface, so that the width of the skirt can reach 65mm, and it is clamps every 200mm.

Place the surface of the panel up on the worktable, check the smoothness of the adhesive surface, wipe off the dirt with clean ball, rinse with clean water, clean and dry with a wind gun or dry cloth to stick to the surface. Evenly smear the coloring and coloring gels on the side side of the panel and the side of the reinforcing bar, put the slope of the skirt on the glue, squeeze the air, clamp the edge of the skirt with the panel with a type clip and use the rubber hammer to moderate the strength, make the skirt and the panel at the corner flat, and clip a clip at every 100-150mm. Clean up residual glue and enter the next procedure after 15 minutes.

artificial quartz stone plant

artificial stone slab machinery suppliers

Quartz stone is the highest in all decorative stones, artificial stone slab machinery suppliers in the production of plate in order to make the appearance more rich, will join the size of different sizes of particles to carry out. Quartzite itself because of the hardness is not easy to process, adding quartz particles for processing is a certain difficulty, processing is the first step is also a very important step, we will look at the following matters to pay attention to.

The first is to select material to see whether there are defects on the surface of the plate (color difference, particle uneven, collapse, spot or patch, scratch or water grinding), and calculate whether or not it can be avoided during the opening process. And how to open the material, so that it can meet the size of the drawings and save materials.

Then the sawing platform is prepared. In order to prevent the rust on the bottom of the open plate, the effect of the quartzite mesa is affected. To avoid the direct contact between the plate and the sawing table, the visible surface of the sawing table should be paving the quartz slab. Diamond saw blades are used for quartzite plates, and the main equipment for cutting is the trimming machine. When the diamond saw blade is installed, the rotation direction of the saw blade is consistent with the rotation direction of the machine (the direction of the saw blade is identified in the direction of the saw blade). Before opening the material, check whether the diamond saw blade is loose after installation. If it is loose, use the necessary spanner to tighten it.

Finally, it is to open the material, gently place the quartz stone plate on the work surface, adjust the board to the right place, and leave the material of the panel one by one. Then adjust the backing plate, then open the skirt plate, water retaining edge and other auxiliary lath. The basic principle of material opening: from a large to a small order. The edge of the water can be processed according to the standard parts. The water retaining edge of each color can be directly opened to the edge grinding process according to the quantity of use. After grinding, the water edge is sent to the water grinding process for water mill, and then placed in the matching area for backup.

artificial quartz slab